List of Torque specs

I haven't seen one of these yet around here. I was thinking someone could get a list of torque specs for fastners on our cars. I am about to go through the top end of my regal and replace all the gaskets but I can't seem to remember the torque specs. I hope this was the right section for this.

Fastener Tightening Specifications


Application
Metric
English

Accelerator Control Cable Bracket Bolt
16 N-m
12 lb ft

Air Injection Check Valve Pipe to Exhaust Manifold
10 N-m
89 lb in

Air Injection Check Valve to Bracket Bolt
25 N-m
18 lb ft

Balance Shaft Driven Gear Bolt
22 + 70° N-m
16 + 70° lb ft

Balance Shaft Retainer Bolt
30 N-m
22 lb ft

Camshaft Position Sensor Bolt
10 N-m
89 lb in

Camshaft Sprocket Bolt
100 + 90° N-m
70 + 90° lb ft

Camshaft Thrust Plate Bolt
15 N-m
11 lb ft

Canister Purge Solenoid Valve Bracket Bolt
50 N-m
37 lb ft

Canister Purge Vacuum Switch Bolt
50 N-m
37 lb ft

Connecting Rod Cap Bolt
27 + 50° N-m
20 + 50° lb ft

Crankshaft Balancer Bolt
150 + 76° N-m
111 + 76° lb ft

Crankshaft Main Bearing Cap Bolt
40 + 110° N-m
30 + 110° lb ft

Crankshaft Main Bearing Cap Bolt (Side)
15 + 45° N-m
11 + 45° lb ft

Crankshaft Position Sensor Stud
30 N-m
22 lb ft

Crankshaft Rear Oil Seal Housing Bolt
15 + 50° N-m
11 + 50° lb ft

Cylinder Head Bolt
50 + 120° N-m
37 + 120° lb ft

Drive Belt Tensioner Bracket Bolt/Nut
50 N-m
37 lb ft

Drive Belt Tensioner Bracket Stud
6 N-m
53 lb in

EGR Valve Adapter Bolt/Stud
50 N-m
37 lb ft

EGR Valve Inlet Pipe Bolt
29 N-m
21 lb ft

EGR Valve Nut
30 N-m
22 lb ft

EGR Valve Outlet Pipe Bolt/Nut
29 N-m
21 lb ft

Engine Block Coolant Drain Plug
30 N-m
22 lb ft

Engine Block Oil Gallery Plug
30 N-m
22 lb ft

Engine Coolant Temp Sensor
23 N-m
16 lb ft

Engine Flywheel Bolt
15 + 50° N-m
11 + 50° lb ft

Engine Front Cover Bolt Stud
20 + 40° N-m
15 + 40° lb ft

Engine Lift Bracket Bolt/Nut./Stud
30 N-m
22 lb ft

Engine Mount Nut Lower
78 N-m
58 lb ft

Engine Mount Nut Upper
78 N-m
58 lb ft

Engine Oil Pressure Indicator Switch
16 N-m
12 lb ft

Engine Wiring Harness Heat Shield Nut/Bolt
10 N-m
89 lb in

Exhaust Crossover Heat Shield Nut
20 N-m
15 lb ft

Exhaust Crossover Pipe Bolt/Stud
18 N-m
13 lb ft

Exhaust Manifold Bolt/Nut
30 N-m
22 lb ft

Exhaust Manifold Stud (Inner)
30 N-m
22 lb ft

Exhaust Manifold Stud (Outer)
10 N-m
89 lb in

Fuel Injector Rail Nut
10 N-m
89 lb in

Fuel Injector Rail Stud
25 N-m
18 lb in

Fuel Injector Sight Shield Bracket Nut
30 N-m
22 lb ft

Generator Brace Bracket Bolt
50 N-m
37 lb ft

Heated Oxygen Sensor
42 N-m
31 lb ft

ICM Nut
50 N-m
37 lb ft

ICM Stud
6 N-m
53 lb in

ICM Wiring Harness Bolt
2 N-m
18 lb in

Idler Pulley Bolt
50 N-m
37 lb ft

Idler Pulley Bracket Bolt
30 N-m
22 lb ft

Lower Intake Manifold Bolt
15 N-m
11 lb ft

Oil Cooler Adapter Connector
50 N-m
37 lb ft

Oil Filter
30 N-m
22 lb ft

Oil Filter Adapter Bolt
15 + 50° N-m
11 + 50° lb ft

Oil Level Indicator Switch
20 N-m
15 lb ft

Oil Level Indicator Tube Nut
19 N-m
14 lb ft

Oil Pan Bolt
14 N-m
125 lb in

Oil Pan Drain Plug
30 N-m
22 lb ft

Oil Pump Cover Screw
11 N-m
98 lb in

Oil Pump Screen Bolt
15 N-m
11 lb ft

Power Brake Booster Heat Shield Nut
20 N-m
15 lb ft

Spark Plug
27 N-m
20 lb ft

Starter Motor Heat Shield Bolt
30 N-m
22 lb ft

Throttle Body Nut
10 N-m
89 lb in

Throttle Body Support Bolt
10 N-m
89 lb in

Throttle Body Support Stud
6 N-m
53 lb in

Timing Chain Dampener Bolt
22 N-m
16 lb ft

Upper Intake Manifold Bolt/Stud
10 N-m
89 lb in

Vacuum Solenoid Valve bolt (with NC1 California Emissions)
10 N-m
89 lb in

Valve Lifter Guide Retainer Bolt
30 N-m
22 lb ft

Valve Rocker Arm Bolt
15 + 90° N-m
11 + 90° lb ft

Valve Rocker Arm Cover Bolt
10 N-m
89 lb in

Water Outlet Bolt
27 N-m
20 lb ft

Water Pump Bolt
15 + 80° N-m
11 + 80° lb ft

Water Pump Pulley Bolt
13 N-m
116 lb in

Wiring Harness Shield Bolt/Nut
10 N-m
89 lb in

WOW thank you very much, that was way more than I expected. Now maybe we can get a sticky made with that info in it.

Might want to check out the How To Section as well....

http://www.grandprixforums.net/torqu...ifications.php

webracin

haha, I didn't even know that was there. I stole it elsewhere. Same place that came from aparently.

Snout bolts 15 lb-ft

I need the specs for the valve body and pump bolts. Also those for the bolts holding the cover over the drive chains. Can anyone please help?

Thanks. Dan