Turn Signal on Solid
This is a discussion on Turn Signal on Solid within the General Tech Discussion forums, part of the W Body Tech category; This is strange, This morning when I started my 01 GP up the right turn signal light on my dash ...
 |
| | LinkBack | Thread Tools | Display Modes |
|
#1
08-19-2008, 01:16 PM
| ||||
| ||||
 Turn Signal on Solid This is strange, This morning when I started my 01 GP up the right turn signal light on my dash & hud was lit solid - checked the signal stalk & it was not switched to the right. Left turn signal works correctly and stays off when turned off. Unplugged the bulb from the right front headlight housing & the light went dim on the dash, but the rear turn signal light is still lit. I can hear a faint buzzing sound coming from under the dash below the steering column when the lights are lit. Only thing I've done recently in that area is removing the ignition switch interlock solenoid to cure the sticking key syndrome, and that was just unplugging it & removing it. Any Ideas??        |
|
#5
08-20-2008, 12:23 AM
| ||||
| ||||
| Re: Turn Signal on Solid agree with badaz^^ its cheaper to replace also.
__________________ 98 chevy truck 83 Olds cutlass 86 Olds cutlass 06 se gold |
|
#6
08-20-2008, 05:00 AM
| ||||
| ||||
| Re: Turn Signal on Solid flasher.....or condensation in the connector......
__________________ 2001 GTP street car- GT45 turbo,Stage 4 Intense turbo cam,FMIC,150 wet, double roller timing chain, Diamond forged coated pistons 8:0:1, Diamond piston rings, cryoed L32 connecting rods, Cryoed crank, Clevite77 main bearings, Clevite77 cam bearings, Clevite77 L32 rod bearings, ARP Everything, Intense/meizere true billet Flexplate, Custom UIM, Intense oil pressure kit, Cometic 4 layer head gaskets, OE-R lifters, Cryoed L67 block, ATI turbo dampner, SDD FATMAN FUEL RAILS!!!!!!!!!  |
|
#8
08-26-2008, 04:40 PM
| ||||
| ||||
| Re: Turn Signal on Solid Did you check the blinker fluide, worked for me.
__________________ If my pics are not working, please email me, I may have moved the pics on a different page on Photobucket. Thanks |
|
#10
08-31-2008, 01:39 AM
| ||||
| ||||
| Re: Turn Signal on Solid I had the same problem with my 95 Riviera, after the blinker stayin on constant it just stopped working all together same buzzing sound, i replaced the turn signal switch and still didnt fix it all relays and fuses were good. I would drive everyday without a turn signal at all. Never figured it out...
__________________  99 GT- L36:GenV:N*:1.9 rollers:Pacesetters:slp catback:3ep trans:Intense Input shaft:stock pulley BPC member |
|
| Bookmarks |
| Tags |
| signal, solid, turn |
| Thread Tools | |
| Display Modes | |
Linear Mode
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Autozone SOLID engine and trans mounts | Abrasive | Parts/Shops/Community Heroes | 34 | 08-17-2009 08:19 PM |
| front turn signals | miller | Visual/Body Modifications | 10 | 12-24-2008 10:24 PM |
| wiper/turn signal switch | GOINDEF | General Tech Discussion | 2 | 05-13-2008 07:52 PM |
| ***FIXED*** Tranny sounds turn out to be far worst.. | evlprx | 3.8L V6 Naturaly Aspirated (L36)(L26) | 11 | 02-22-2008 07:55 AM |
| Exterior Fog/Turn Signal and Interior Window Controls | POLECAT2007 | Visual/Body Modifications | 1 | 02-16-2008 03:31 PM |
All times are GMT -5. The time now is 08:53 PM.
Powered by vBulletin
Copyright ©2000 - 2010, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.5.0 RC2 ©2010, Crawlability, Inc.
Copyright ©2000 - 2010, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.5.0 RC2 ©2010, Crawlability, Inc.