Quote:
|
Originally Posted by Curtis  Has anyone seen the engine bay of a Bonneville? 3800 series II, no dog bones! |
but the engine mount goes THROUGH the serp belt.....
ick!
| Register FAQ MembersCalendar SearchToday |
This is a discussion on Engine mount idea within the Pontiac Grand Prix forums, part of the W Body Specific category; Originally Posted by Curtis Has anyone seen the engine bay of a Bonneville? 3800 series II, no dog bones! but ...
| |||||||
03-05-2008, 12:23 AM
| #21 | |
| GTP Level Member  Join Date: Jan 2008 Location: SW Chicago Suburbs
Posts: 1,564
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (0) Rep Power: 2    |  Re: Engine mount idea Quote:
but the engine mount goes THROUGH the serp belt..... ick! | |
|        |
|
03-05-2008, 09:14 AM
| #22 | |
| GTX Level Member  Join Date: Dec 2007 Location: Middleburg, PA
Posts: 922
Thanks: 0
Thanked 4 Times in 4 Posts
iTrader: (0) Rep Power: 1  | Re: Engine mount idea Quote:
And the engine still rocks more than my GTPs engine does.
__________________ 1997 GTP - 196xxx miles, PEMs, 3" SS Exhaust w/ Borla Mufflers, 3.4", 180* stat(summer), FWI, 1.84 RR, PT, SLP hood, KYB GR2s, GMPP Handling Kit, etc... | |
|
| |
|
03-07-2008, 06:52 PM
| #23 |
| GTX Level Member  Join Date: Jan 2008 Location: Charlotte
Posts: 895
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (1) Rep Power: 1 | Re: Engine mount idea Am I just lucky? I have the 3800 polished dogbones and the Intense poly bushings for them and for the front brackets and I havent noticed any vibration. I installed them last week and have drove the car a few short drives.
__________________ http://www.cardomain.com/ride/2619487 2008 Spring Autofair "Best Of Show" 2007 Fall Autofair " Best Of Show" 2007 Spring Autofair "Cleanest Engine Bay" |
|
| |
|
06-04-2008, 09:56 AM
| #24 |
| SE Level Member  Join Date: May 2008 Location: Houston, TX
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (0) Rep Power: 0 | Re: Engine mount idea Not sure if this will work for you, but I just installed the shortened dogbone mounts: Shortened Dogbones (Reduces vibration on lowered cars) and about 99% of my vibration has been eliminated. However, my vibration was caused by lowering the car, not the poly mounts. Took 10 minutes to install and, in my opinion, worth every bit of the $25. Hope this helps some of you. Ciao, |
|
| |
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
| |
| ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Bombproof Poly Trans mount | Trannyman95 | Necessity Corner | 36 | 03-23-2008 04:56 PM |
| car and Engine pics | Jason Austin | Appearance | 14 | 01-07-2008 09:18 PM |
| Pics of polished stuff in engine bay | quikgtp | 3.8L V6 Supercharged (L67)(L32) | 19 | 01-05-2008 11:09 AM |
| LS9 Corevette Engine, Supercharged | SyntheticShield | The Lounge | 33 | 01-03-2008 01:28 PM |
| New pics of my tint job and painted engine parts | ryangtp89 | The Lounge | 3 | 12-27-2007 12:15 AM |
Linear Mode
