This is a discussion on Q? Output Shaft removal within the W Body 1997 to current 4 speed Automatic (4T65E) (4T65E-HD) forums, part of the W Body Tech category; OK, I guess I'm either going cabin crazy or just plain confused on the directions for removing the differential from ...
| |||||||
06-21-2008, 03:54 PM
| #1 | |
| SE Level Member  Join Date: Mar 2008 Location: Houston, TX
Posts: 41
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (0)   |  Q? Output Shaft removal OK, I guess I'm either going cabin crazy or just plain confused on the directions for removing the differential from the output shaft of the tranny. The directions say (and show) to wedge the tool between the output shaft and the horizontal bar inside the differential. The directions say this: Quote:
 | |
|        |
|
06-21-2008, 09:26 PM
| #2 |
| Transmission Expert  Join Date: Dec 2007 Location: Fort Wayne, IN
Posts: 1,275
Thanks: 0
Thanked 23 Times in 21 Posts
iTrader: (3) | Re: Q? Output Shaft removal Read step 2 again, you just put a chisel in between the output shaft and diff shaft and smack it with a hammer and it will pop loose.
__________________ www.TripleEdgePerformance.com 4T65E Transmission Info Voted GPF.net Community Hero  |
|
| |
|
06-22-2008, 12:51 AM
| #3 |
| SE Level Member  Join Date: Dec 2007 Location: Schaumburg
Posts: 114
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (0) | Re: Q? Output Shaft removal If yours is a 97, that picture isn't right. I ended up hitting mine twice lightly with a hammer when I realized it isn't one of those compression rings. The 97 has a c-clip that needs to be popped off with either a specail tool or I used two screw drivers pushing both down at the same time.
__________________ 1997 Black GTP 72k (4dr), 3.5 Pulley, Wbody Downpipe, Wbody Shift kit (street), DHP 1.0, NGK TR55ix Spark Plugs, GMP Handling kit, KYB AGX Struts, AT Italia Inox 235x50x18 Bfgoodrich KDWS, GMPP Springs, Corvette C5 Calipers, Blazertech 3200, DHP Powertuner (97-03), Built Trans, Torsen Diff |
|
| |
|
06-22-2008, 02:59 AM
| #4 |
| Transmission Expert Join Date: Dec 2007 Location: Fort Wayne, IN
Posts: 1,275
Thanks: 0
Thanked 23 Times in 21 Posts
iTrader: (3) | Re: Q? Output Shaft removal Correct, for 97s this wont work and you need a special c-clip removal tool specific for this clip OR you can use to screwdrives and push the clip off. IIRC his car was newer than a 97 and why I didnt mention it above. Edit..... Here is a link to a thread of a diff install that shows where to put the chisel and you have to smack it with a hammer to shock the shaft/snap ring to pop out the axle. http://www.grandprixforums.net/f21/4...pics-1928.html (4T65E Differential INSTALL PICS!!!)
__________________ www.TripleEdgePerformance.com 4T65E Transmission Info Voted GPF.net Community Hero |
|
| |
|
06-22-2008, 10:07 AM
| #5 |
| SE Level Member Join Date: Mar 2008 Location: Houston, TX
Posts: 41
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (0) | Re: Q? Output Shaft removal I guess I didn't specify what year my car is.... it's a 99 GP GT. I did see your write up, but spaced it out. Thanks. I guess I need a bigger chisel. |
|
| |
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
| |
| ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| CV Shaft | webracin | Parts Best Buys | 14 | 04-15-2008 02:38 AM |
| Effect Of NightShade On Light Output | SyntheticShield | Appearance | 32 | 02-08-2008 08:36 PM |
| WTB: Intense input shaft | shaferz | Wanted Items | 1 | 01-12-2008 10:59 AM |
| REPAIR CV Shaft Replacement [*] | webracin | How To Write-Ups | 0 | 12-21-2007 06:59 PM |
| REPAIR CV Shaft Rebuild/Replace [*] | Reptile | How To Write-Ups | 9 | 12-20-2007 12:59 PM |
Linear Mode
