So the last few weeks have been chalked full of problems/roadblocks. Just got the car back from the shop after a 183.00 repair bill for a Fuel resistor. Makes me a little sad the labor was more than the actual part (Part 58.00 Labor 110.00). Anyhow its back and runs better than the day I got it.

So after a few days of pondering I deceided to try installing the new seats I picked up from a local GTP owner. Got the two buckets for 28 bucks. So I pull the passenger side out and go to install the new one, won't clip into place. I reach back to grab the release on the back and it's not there. I have a coupe and the new seats came from a sedan. Figured they would be the same, never in a million did I think about them not leaning forward enough to clip in the front mounts. Checked the driver side and same deal.

So my question is has anyone run into this and does anyone have any suggestions? I've thought of trying to pull the seats apart and use my frames but use the leather and support from the new ones. Never done any uphol work before and don't want to trash the new seats.

Not sure if the do, but see if the tracks from the two sets of seat unbolt and see if they can be swapped. Let me know what your findings are and we can go from there.

__________________

97 GTP~K&N Cold Air Intake~3.4" S/C Pulley~Cat Back Exhaust~MSD Blaster Coil Packs~MSD 8.5mm Wires~NGK TR55IX Plugs~More To Come

sedan seats are way different, but should bolt to your tracks, just remember you lose the forward flip feature (don't need that with 4 doors)

__________________
Steve
'97 GTP VS cam, ZZP PCM, and not much else yet

Put em in the rear.

__________________
1998 GTP

They'll fit. It's the same seat minus the 'fold down' feature to allow people into the back of the car, but there is no reason they won't fit and bolt in just like the coupe seats.

__________________

2.8 Pulley, Intense IC, P&P Gen V, Machined Intake, Intense PCM, 65lb/hr Injectors, N* Throttle Body, 1 3/4" Headers, 3" Exhaust, Intense Shift Kit, 3.69:1 Gears, 4000 Stall, N20

I hate that! Thats just me though...it is different though.

__________________
1999 Silver GTP~HP Tuners~XP cam~ZZP FS Intercooler~ZZP 78mm Billet Throttlebody~LQ4 MAF~Lucas 42.5's~Coated Pacesetters~2.8 MPS~PRJ fuel logs~Ported & Polished S/C~JMB fwi ~Built Tranny-3.29's-7/8's chain-Intense forged Input Shaft~

Running mid-high 12's

the tracks are different especially the passenger one (doesn't have the slide feature for easy entry)

__________________
Steve
'97 GTP VS cam, ZZP PCM, and not much else yet

Yeah but they will still fit. Didn't say it was going to slide up for easy entry.

__________________

2.8 Pulley, Intense IC, P&P Gen V, Machined Intake, Intense PCM, 65lb/hr Injectors, N* Throttle Body, 1 3/4" Headers, 3" Exhaust, Intense Shift Kit, 3.69:1 Gears, 4000 Stall, N20

isent it going to make it a pain in the ass to get in the back then?? why not wait and get some coupe seats so you dont have as many issuies??

__________________
white 04 comg G gtp. intake plug and wires (for now)
14.6 1/4. 2.1 60" on badly gaped plugs

You could probably check with a couple scrap yards and see if they would swap seats with you. Might get lucky.

__________________

97 GTP~K&N Cold Air Intake~3.4" S/C Pulley~Cat Back Exhaust~MSD Blaster Coil Packs~MSD 8.5mm Wires~NGK TR55IX Plugs~More To Come