| Register FAQ MembersCalendar SearchToday |
This is a discussion on curious... within the The Lounge forums, part of the General Forum category; does anyone know of a write-up for installing a hvtb...mine comes tomorrow and i want to make sure i do ...
| |||||||
05-05-2008, 04:45 PM
| #1 |
| GT Level Member  Join Date: Dec 2007 Location: Fayetteville, NY
Posts: 424
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (0)   |  curious... does anyone know of a write-up for installing a hvtb...mine comes tomorrow and i want to make sure i do everything right...i dont think it would be too hard, but just want to make sure you know?...
__________________ http://www.cardomain.com/ride/2556536 NKG Iridium Plugs, 8mm Spiro Wires, ZZP Reprogrammed PCM, ZZP 3" full cat, ZZP Ceramic Coated Ported Manifolds, ZZP HV3, ZZP HVTB, ZZP ER Ratio Rocker Arms, ZZP Drilled 180* Thermostat, MotorSports Performance Intake, Reptile's IAT and dezldave tuned |
|        |
|
05-05-2008, 08:02 PM
| #2 |
| GTP Level Member  | Re: curious... unless you tear your gasket or it doesnt pull off in one piece (or the rubber surrounding it is messed up) i dont see you having any problems.
__________________ 98 XGT - 3.2/3.4, s&s, ported m90/TB/LIM, 1.9s, jp dbl; tinted, blacked out, lowered soon -> e85, meth, and a lot smaller pulley  |
|
| |
|
05-05-2008, 09:18 PM
| #3 |
| GT Level Member Join Date: Dec 2007 Location: Fayetteville, NY
Posts: 424
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (0) | Re: curious... oh ok
__________________ http://www.cardomain.com/ride/2556536 NKG Iridium Plugs, 8mm Spiro Wires, ZZP Reprogrammed PCM, ZZP 3" full cat, ZZP Ceramic Coated Ported Manifolds, ZZP HV3, ZZP HVTB, ZZP ER Ratio Rocker Arms, ZZP Drilled 180* Thermostat, MotorSports Performance Intake, Reptile's IAT and dezldave tuned |
|
| |
|
05-09-2008, 02:58 PM
| #4 |
| GT Level Member  Join Date: Jan 2008 Location: Charleston SC, originally from NH
Posts: 169
Thanks: 0
Thanked 0 Times in 0 Posts
iTrader: (0) | Re: curious... It's not hard. Unbolt the throttle cable bracket (or if the new throttle body has the brackets already on it, you can just remove the cables). The throttle body is held on by three bolts, and maybe a bracket underneath. You can take the stud out of your old throttle body for the bracket, or just leave it off. Good luck!
__________________ David's 2002 Redfire Metallic Grand Prix GT 180* T-Stat, Alt. Rewire, Stage 1 HVTB, Wizaired CAI, ZZP 1.0 PCM, Intense Shift Kit KYB AGX Struts, Vogtland Springs, Speedbuilt STB's, GMPP Handling Kit, 12" Brakes |
|
| |
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
| |
| ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Question Just Curious.. | GP2003GT | Appearance | 13 | 04-14-2008 12:08 PM |
Linear Mode
